Corrugated cardboard cold glue laminating machine 1350*1100 mm 380
V food packaging
1. Suitable for laminating of cardboard and corrugated cardboard in
150-600 g/m2 .
2. The vacuum suction-type feeding system can lead the paper
accurately into the machine;cycle stacking planes in a state of
non-stop the next batch of paper stack well, so that more
3. Using suction automatic feeding of bottom sheet, according to
the main machine operating speed, continuous automatic tracking.
4. The machine operation is stable, surface paper with corrugated
paper joint very accurate. The corrugated paper never pull ahead,
surface paper's location is easy adjust.
5. Machine uses touch-screen/PLC/servo motor control system, double
frequency control type , the circuit system is stable, and can
automatically display the failure alarm.
6. Automatic gluing, and the glue can be used circulatory, avoid
7. Measure roller line-speed design scientifically, avoid glue fly
out when the speed is high.
8. Pressure rollers adopt unilateral adjustment, convenient and
9. Cleaning type : bottom roller is extruded by rubber roller to
clean the bottom laminating pressure roller, ensure the cleaner on
the reverse of the bottom paper . Make glue etc. foreign matter
after washing direct subside in tank. At the same time , adopting
the gear and chain to control the lifting of tank, can take out the
tank easily and convenient to wash .
10. The pressure conveyor adopt floating movable structure , total
length 5m , equipped with 28 paper pressing rollers , make the
cardboard uniform bearing strength in pressing process.
11. Counter designs scientifically, easy recording the amount you
have been worked.
12. Small pressure table (optional) . length 2.5m , big pressure
table length 5m.
|Model||SMTM-QZD1300A||SMTM-QZD 1450A||SMTM-QZD 1550A||SMTM-QZD1650A|
Max laminating size
Min laminating size
|Weight||About 4.8t||About 5t||About 5.2t||About 5.4t|
Bottom paper thickness
|A/B/C/E flute, 3/4/5 layer , less than 12mm thickness|
Surface paper gram weight
|Display screen||Delta (Taiwan)|
|Switching power supply||OMRON|
|Mainframe Motor||Tianjin Tong'de'li|
|Geared motors||Shanghai Renmin|
|Vacuum pump||EUROVAC (Taiwan)|
|Vortex Pump||Shanghai Hengli|
|Synchronous belt||Ningbo Beidi (Joint venture)|
|The host chain||CHOHO (sino-Japanese Joint venture)|
|Transfer press belt||Italy (Joint venture)|
|Contactor||SCHNEIDER (The French)|
|The host inverter||Delta (Taiwan)|
|Pressure platform inverter||Delta (Taiwan)|
|Pressure platform motor||Shanghai OTT|
Unit Introduction :
High precision high speed feeder , make the feeding smooth .
Strengthen type feeder device , the suction mouth angle can be
adjustable , according to different kinds of surface paper .
Electric system :
Main electric appliances all adopt the imported famous brand .
PLC tracking technique , automatic fault detection .
Pressure adjustment system :
Adjust the pressure in single side , to ensure the pressure is same
on both sides .
With pressure gauge display , can easily adjust when change the
Pressure conveyor :
Floating type pressure design , don’t need to adjust the pressure
of flatbed .
Heightening design , good for the smooth work of thick corrugated
(please read this manual carefully before installing and using the
Attention for safety :
Device peripheral environment setting
Please set the machine in a firework-free environment to prevent
Please set the machine in an environment with sufficient
ventilation (if necessary, please install ventilation in the
surrounding environment of the machine). To ensure a good working
environment for employees.
The surrounding environment of the equipment should be provided
with adequate natural lighting.
The equipment has no dust, noise, oil pollution and other pollution
to the surrounding environment.
Please use proper lifting tools and moving equipment when carrying
this machine (use soft materials cushion if necessary) , to prevent
equipment damage and other injuries.
When installing the machine, please follow the instructions (if
necessary, the company's technical staff should be provided with
Please check the instructions carefully before wiring to make sure
the correct power supply is input.
Make sure the input power is disconnected, and then wire it. To
avoid electric shock.
Good grounding is necessary to avoid electrical shock or fire.
The business shall be conducted by a full-time electrician to avoid
electric shock or fire.
Before running, please make sure that the motor runs correctly.
Before running, please check the transmission mechanism of each
part of the machine to make sure that the transmission mechanism of
each part runs well.
Test run for about 10 minutes and make sure that the whole machine
Please give the operator the necessary pre-job training.
Test all emergency stop switches before operation.
All safety switches and protective devices must be properly
installed and used.
Make sure all debris is cleared from the conveyor belt and stacking
table before starting up. Otherwise it may cause the machine
injuries or personal injuries.
Avoid talking with others while operating the machine. Distraction
can lead to human injuries or even serious accidents.
Prepare well in advance so that you can handle all possible
emergencies with what you can reach. Improper handling can lead to
The rotating roller is dangerous and may cause serious injury. Do
not open the safety protection device when starting up. Only can
use the jog function after opening the safety protection device.
Do not start the machine at will when the life of a person is at
risk or the machine is in maintenance state.
During the operation, debugging, installation and maintenance of
the machine, do not wear loose clothes, accessories or with long
hair hangs out .
The gap of each roller should be adjusted. The gap between the glue
distribution roller and upper roller and lower roller cannot be
adjusted to zero , to avoid roller friction between them.
The rubber pump cannot be operated without load to avoid friction
damage of the rubber pump impeller.
Please do not change or damage the settings of the main motor
Please establish the rules and regulations for equipment
maintenance and strict implementation.
The machine must be thoroughly checked and tested before being put
back into use after being idle for a long time.
The water in the water tank of the cleaning roller should be
replaced for a period of time to keep the water clean.
Please use the spare parts produced by our company for maintenance
and replacement, which is caused by the use of spare parts from
other companies, no warranty will be given for mechanical damage.
Without the permission of our technical personnel, we decline any
modification of the machine in any situation, and our company will
not assume any responsibility for the modification of the machine
by users themselves.
Surface paper is fed by automatic paper feeder and transported by
conveyor belt to the front initiating and static positioning, the
photoelectric switch control vortex pump to open the suction valve
after get the signal, adsorb the bottom paper on the suction belt,
then suction motor rotate to output the bottom paper automatically,
after coating of glue in glue part to the front initiating ,
positioning and alignment with surface paper, at the same time with
the help of the thrust of the roller against the bottom paper to
open the initiating structure, surface paper and bottom paper paste
together by the pressure of laminating roller and pressing roller,
and sent to pressing parts.
Preparation before starting the machine: adjust the gap distance of
the paper feeding rollers, about the 85-90% of the bottom paper
thickness, the gap between the laminating rollers is 85-90% of the
total thickness of surface paper and bottom paper. Suitable size
and pressure adjustment in feeder.
After the adjustment, clean the water pump automatically and fill
the sink with water. Put the scraper onto the tank, not too tight
or loose , just touch the surface of roller naturally .
After adjusting the clearance, need test running before work (do
not apply glue first). Order: a: switch on the power; b: Rotate the
adjustment knob until the display value of about 15Hz on the
screen. c: start the main motor. d: simultaneously open the feeder
to feed paper, feed air pump, pressing part and air pump.
When the machine start to laminate paper, 20-30 pieces of paper
need to be glued together for self-adjustment, which belongs to the
automatic calibration stage, and can only be adjusted at will after
the paper feeding parameters are stable. Note that the change of
paper feeding parameters can not be adjusted without stability,
otherwise it will cause a large error in laminating between surface
paper and bottom paper. Recommendation: when the machine is in
self-calibrate, users can use the same specification of waste
paper, so that it will not cause more waste.
When the above procedures are completed, the glue pump can be
started to adjust and work.
Suction belt not rotate
The photoelectric switch doesn't work.
Adjust the photoelectric switch
The servo motor does not work.
Adjust the servo driver.
Bottom paper can’t feed automatically or feed more than one piece
in one time .
the clearance of paper-separating head is too big or small .
Adjust the clearance of paper-separating head
Wind power is too small or big
Adjust the air volume.
Paper feeding is not in place
Adjust the paper position
Front initiating position is not right
Adjust the hand wheel of front initiating .
The pressure in both ends of roller is not same .
Adjust the pressure to be same .
Glue ran out when the two pieces of paper were glued together.
The clearance of laminating roller or pressing roller is too small
Adjust the clearance
The glue feeding volume is too big
Adjust the glue volume.
The glue on the bottom paper is uneven.
The both ends of glue roller and glue distribution roller are not
Adjust the parallelism between rollers.
The both ends of upper glue roller and lower glue roller are not